Equipment Services Trailers Permits Cost How it works About Contact
Get a quote Español

(727) 342-1152 · sales@247shipping.net

Home / Trailers

The trailer decides the price.

The lower the deck, the taller the machine can be and still stay legal. Legal means no permit, no escort, fewer rules about when it can drive. So the first thing we work out is the lowest-cost trailer that keeps your machine under the limits, and when none can, which one makes the oversize move simplest.

24/7 Shipping Inc. is a licensed freight broker, MC 1629455. We arrange your move with vetted carriers.

Try it

What hauls my machine

Put in the size and weight you have. The answer is a first read; we confirm it against the make and model before you get a number.

What hauls my machine?

Type the shipping size. You get the trailer, and whether to expect permits or escorts.

Decimals are fine: 10 ft 6 in = 10.5. Do not know? Skip this and send us make and model.

Enter at least width, height and weight to see the answer.

Side by side

The trailers, compared

Heights are measured from the road. The legal height in most states is about 13 ft 6 in on the trailer (14 ft in some western states), so the deck height decides how tall the freight can be. All figures are approximate; decks vary by trailer.

TrailerDeck heightTallest freight that stays legalWhat it carriesHow it loads
FlatbedAbout 5 ftAbout 8 ft 6 inLow machines, attachments, steel, crated freightForklift, crane, or a loading dock; ramps for some machines
Step deckLower deck about 3 ft 4 inAbout 10 ftMid-height machines: skid steers, backhoes, small loaders, tractorsRamps at the back; drive on
Double dropA low well between a raised front and a raised backClose to a lowboy, in the wellTall machines that are long but not very heavyOver the front if the neck comes off; otherwise ramps or a crane
Lowboy / RGNAbout 18 to 24 inAbout 11 ft 6 in to 12 ftExcavators, dozers, large loaders, cranes; the heavy and the tallRGN: the neck comes off and the machine drives on over the front. Fixed neck: ramps
Stretch trailersSame as the base trailer (flatbed, step deck or lowboy)Same as the base trailerLong freight: beams, booms, long attachments, long machinesThe deck slides out to the length needed; crane or forklift for most freight
Hotshot gooseneckHigher than a lowboy; behind a pickupDepends on the deck; meant for smaller machinesLighter machines, roughly under 15,000 lb: minis, skid steers, small tractorsRamps at the back; drive on
Tilt / LandollThe whole deck tilts down to the groundDepends on the trailerMachines that do not run, forklifts, low-clearance freightDriven or winched up the tilted deck, no ramps

Weight counts as much as height. A truck and lowboy weigh roughly 32,000 to 35,000 lb empty, so about 45,000 to 48,000 lb of machine is the most a standard 5-axle setup carries under the 80,000 lb limit. Heavier takes more axles and an overweight permit. How permits work

How we choose

When we book each one

We do not own trailers. We book the carrier that runs the right one on your lane, and the right one is usually the cheapest trailer that keeps your machine legal.

Flatbed

When the freight is low enough to stay under the legal height from a deck about 5 ft up, and it can be lifted on. Lifting it on means a forklift, a crane or a dock at both ends.

Step deck

When the machine is too tall for a flatbed but stays under about 10 ft, and it can drive up ramps. This is where many skid steers, backhoes and tractors ride.

Double drop

When a tall machine needs a low deck with a long well, or when the carrier on your lane runs one. The choice between this and a lowboy depends on the machine, its weight and how it loads.

Lowboy / RGN

When the machine is tall, heavy or both. A deck about 18 to 24 in off the road keeps freight up to about 11 ft 6 in to 12 ft legal. An RGN is the pick for tracked machines that drive on over the front.

Stretch trailers

When the freight is too long for a standard deck: long beams, crane booms, long attachments. Tell us the full length, attachments on, so the carrier can plan the trailer and the route.

Hotshot gooseneck

When the machine is light, roughly under 15,000 lb, like many minis and skid steers. A machine that size does not need a full semi-truck setup, so you do not pay for one.

Tilt / Landoll

When the machine does not run, sits very low, or should not climb ramps. The deck tilts to the ground and a winch pulls it on.

Questions

Straight answers

What is the difference between a lowboy and an RGN?

Both have a deck about 18 to 24 inches off the ground. On an RGN (removable gooseneck) the neck comes off, so the front drops to the ground and a machine drives on over the front. A fixed-neck lowboy loads over ramps at the back.

Can my machine go on a regular flatbed?

Only if it is low enough. A flatbed deck sits about 5 feet up, so freight taller than about 8 feet 6 inches goes over the legal height in most states. Many smaller machines fit; most mid-size and larger ones need a step deck or a lowboy.

Do I have to pick the trailer myself?

No. Give us make, model and what is attached, and we work out the trailer. The tool on this page shows you the same logic if you want to see it first.

When is a hotshot enough?

A hotshot is a pickup pulling a gooseneck trailer. It fits lighter machines, roughly under 15,000 lb, such as many mini excavators, skid steers and small tractors. Heavier machines go on a semi-truck trailer.

What if no trailer keeps my machine legal?

Then it moves oversize: the carrier buys permits in every state on the route, and escorts are added where the width or height calls for them. Those costs are in your quote from the start.

Got a machine to move?

Tell us what it is and where it is going. A person answers, asks the right questions once, and gives you one number.

Call Text Get a quote